MMIO registers: Difference between revisions

From SNESdev Wiki
Jump to navigationJump to search
m (16-bit register formatting.)
(references section)
 
(22 intermediate revisions by 2 users not shown)
Line 1: Line 1:
TODO
This page covers 5A22, APU, and WRAM memory-mapped registers.
* For PPU-related MMIO registers '''$2100-$213F''', see [[PPU registers]].
* For DMA-related MMIO registers '''$4300-$437F''', see [[DMA registers]].
* For a complete summary table of all MMIO registers, see [[MMIO register table]].


* $2100-213F [[PPU registers]]
{| class="wikitable"
* $2140-2413 APUIO
|+ 5A22, APU, and WRAM register summary
* $2180 WMDATA
|-
* $2181-2183 WMADD
! Name
* $4016 Legacy Gamepad 1
! Address
* $4017 Legacy Gamepad 2
! Bits
* $4200 NMITIMEN
! Type
* $4201 WRIO
! Notes
* $4202-4203 WRMPY
|-
* $4204-4206 WRDIV
{{:MMIO register table/MMIO}}
* $4207-4208 HTIME
|-
* $4209-420A VTIME
! colspan=5 | <small>[[MMIO register table/MMIO|table source]]</small>
* $420B MDMAEN
|}
* $420C HDMAEN
 
* $420D MEMSEL
Register types:
* $420E-420F ?
* '''R''' - Readable
* $4210 RDNMI
* '''W''' - Writeable
* $4211 TIMEUP
* '''8''' - 8-bit access only
* $4212 HVBJOY
* '''16''' - 8-bit access to either address, or 16-bit access to the lower address.
* $4213 RDIO
* '''24''' - 8-bit or 16-bit access to 3 registers.
* $4214-4215 RDDIV
* $4216-4217 RDMPY
* $4218-421F STD CNTRL1-4
* $4300-437F [[DMA registers]]


==Interrupts==
==Interrupts==
Line 41: Line 40:
  |          11 = IRQ when V counter == VTIME and H counter == HTIME
  |          11 = IRQ when V counter == VTIME and H counter == HTIME
  +--------- Vblank NMI enable
  +--------- Vblank NMI enable
On power-on: NMITIMEN = $00
On reset:    NMITIMEN = $00


TODO: Details on the exact conditions for an NMI or IRQ.
* If the vblank NMI is enabled, then an NMI will occur at the start of vblank. More precisely, an NMI occurs whenever the bitwise AND of vblank NMI enable and RDNMI's vblank flag becomes 1. As a result, it is possible to get multiple NMIs for a single vblank if vblank NMI is disabled and enabled again while the vblank flag is still 1. This can be prevented by reading RDNMI, which clears the vblank flag.
* TODO: Details on the exact conditions for an IRQ.
* Auto-read runs shortly after the beginning of vblank, reading the current state of the two controller ports into the [[#JOY1|JOY1-4]] registers without halting the CPU. It is equivalent to writing 1 and then 0 to [[#JOYOUT|JOYOUT]] (used for latching standard controllers) and then reading [[#JOYSER0|JOYSER0]] and [[#JOYSER1|JOYSER1]] 16 times each. The controllers are then left in this state so that additional reads can be done manually from JOYSER0 and JOYSER1 to get any additional data, though this is unnecessary for standard controllers. Auto-read takes approximately 3 scanlines, during which the JOYOUT, JOYSER0, and JOYSER1 registers should not be manually accessed.


===Screen timer values===
===Screen timer values===
Line 52: Line 56:
  7  bit  0  7  bit  0
  7  bit  0  7  bit  0
  ---- ----  ---- ----
  ---- ----  ---- ----
  .... ...H  HHHH HHHH
  .... ...H  LLLL LLLL
         |  |||| ||||
         |  |||| ||||
         +---++++-++++- H counter target for timer IRQ
         +---++++-++++- H counter target for timer IRQ
On power-on: HTIME = $1FF


Note that setting a value larger than the maximum H counter value of 339 will prevent the timer's H condition from being met.
Note that setting a value larger than the maximum H counter value of 339 will prevent the timer's H condition from being met.
Line 64: Line 70:
  7  bit  0  7  bit  0
  7  bit  0  7  bit  0
  ---- ----  ---- ----
  ---- ----  ---- ----
  .... ...V   VVVV VVVV
  .... ...H   LLLL LLLL
         |  |||| ||||
         |  |||| ||||
         +---++++-++++- V counter target for timer IRQ
         +---++++-++++- V counter target for timer IRQ
On power-on: VTIME = $1FF


Note that setting a value larger than the maximum V counter value will prevent the timer's V condition from being met. The maximum depends on the region (261 for NTSC, 311 for PAL) and interlacing (1 additional scanline every other frame).
Note that setting a value larger than the maximum V counter value will prevent the timer's V condition from being met. The maximum depends on the region (261 for NTSC, 311 for PAL) and interlacing (1 additional scanline every other frame).
Line 79: Line 87:
  |||| ||||
  |||| ||||
  |||| ++++- CPU version
  |||| ++++- CPU version
  |+++------ Open bus
  |+++------ (Open bus)
  +--------- Vblank flag
  +--------- Vblank flag
   
   
  On read: RDNMI D7 = 0
On power-on: RDNMI = RDNMI & $7F
On reset:    RDNMI = RDNMI & $7F
  On read:     RDNMI = RDNMI & $7F


The vblank flag is set at the start of vblank and cleared at the end of vblank or on read.
The vblank flag is set at the start of vblank and cleared at the end of vblank or on read.
Line 92: Line 102:
  Txxx xxxx
  Txxx xxxx
  |||| ||||
  |||| ||||
  |+++-++++- Open bus
  |+++-++++- (Open bus)
  +--------- Timer flag
  +--------- Timer flag
   
   
  On read: TIMEUP D7 = 0
On power-on: TIMEUP = TIMEUP & $7F
On reset:    TIMEUP = TIMEUP & $7F
  On read:     TIMEUP = TIMEUP & $7F


The timer flag is set when the timer condition specified in NMITIMEN becomes true and is cleared on read.
The timer flag is set when the timer condition specified in NMITIMEN becomes true and is cleared on read.
Line 106: Line 118:
  |||| ||||
  |||| ||||
  |||| |||+- Joypad auto-read in-progress flag
  |||| |||+- Joypad auto-read in-progress flag
  ||++-+++-- Open bus
  ||++-+++-- (Open bus)
  |+-------- Hblank flag
  |+-------- Hblank flag
  +--------- Vblank flag
  +--------- Vblank flag
* J - Set during joypad auto-read.
* H - Set during horizontal blank period.
* V - Set during vertical blank period.
When enabled via [[#NMITIMEN|NMITIMEN]], auto-read begins between H=32.5 and H=95.5 of the first vblank scanline, and ends 4224 master cycles later.<ref>Auto Joypad Read timings from Anomie's timing.txt document.</ref>
==APU==
{{Anchor|APUIOn}}
===APUIOn - Data-to-APU register n ($214n write) (n = 0..3)===
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Data to APU
===APUIOn - Data-from-APU register n ($214n read) (n = 0..3)===
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Data from APU
When the SPC700 reads from $F4+n in its address space, it receives the last value written to APUIOn. When APUIOn is read, the value received is the last one written by the SPC700 to $F4+n. If APUIOn is read while its corresponding $F4+n register is being written, the value read will be the bitwise OR of the old and new values.
These registers are mirrored across $2140-217F.
==WRAM==
{{Anchor|WMDATA}}
===WMDATA - S-WRAM data access ($2180 read/write)===
----
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- S-WRAM data
On write: [WMADD] = value
          WMADD = WMADD + 1
This register's presence on the peripheral bus allows DMA between S-WRAM and another, different source.
Because DMA simultaneously accesses the source and destination, S-WRAM cannot succesfully be both because it cannot simultaneously read from and write to itself. DMA from S-WRAM to this register has no effect, and DMA from this register to S-WRAM writes open bus. In both cases, the address is not incremented.
{{Anchor|WMADD}}
===WMADDL, WMADDM, WMADDH - S-WRAM address ($2181, $2182, $2183 write)===
----
  WMADDH      WMADDM      WMADDL
  $2183      $2182      $2181
7  bit  0  7  bit  0  7  bit  0
---- ----  ---- ----  ---- ----
.... ...H  MMMM MMMM  LLLL LLLL
        |  |||| ||||  |||| ||||
        +---++++-++++---++++-++++- S-WRAM address for WMDATA
DMA from S-WRAM to these registers has no effect.
==ROM==
{{Anchor|MEMSEL}}
===MEMSEL - ROM access speed ($420D write)===
  7  bit  0
  ---- ----
  .... ...F
          |
          +- FastROM enable
On power-on: MEMSEL = $00
If enabled, ROM access to banks $80-FF takes only 6 system clock cycles instead of 8.
==Joypads==
===Joypad NES-style interface===
----
{{Anchor|JOYOUT}}
====JOYOUT - Joypad output ($4016 write)====
7  bit  0
---- ----
.... .210
      |||
      ||+- OUT0
      ++-- OUT2-1 (not connected)
OUT0 is used by standard controllers to latch the current button state. OUT2-1 are not connected in standard consoles, but may be used in the [[Super Famicom Box]] hotel system.
{{Anchor|JOYSER0}}
====JOYSER0 - Joypad serial data port 1 ($4016 read)====
7  bit  0
---- ----
xxxx xxDD
|||| ||||
|||| ||++- Joypad port 1 data 2-1
++++-++--- (Open bus)
On read: Joypad port 1 is clocked (via joypad 1 /OE)
{{Anchor|JOYSER1}}
====JOYSER1 - Joypad serial data port 2 ($4017 read)====
7  bit  0
---- ----
xxx1 11DD
|||| ||||
|||| ||++- Joypad port 2 data 2-1
|||+-++--- Joypad 2 D4-2 (always 1)
+++------- (Open bus)
On read: Joypad port 2 is clocked (via joypad 2 /OE)
The CPU has 5 joypad 2 inputs. Joypad port 2's data 2 and 1 pins connect to D1-0, while D4-2 are tied to ground (and thus read as 1).
===Joypad I/O interface===
----
{{Anchor|WRIO}}
====WRIO - Write I/O ($4201 write)====
7  bit  0
---- ----
21DD DDDD
|||| ||||
||++-++++- CPU I/O D5-0 (not connected)
|+-------- Joypad port 1 I/O
+--------- Joypad port 2 I/O, and
            PPU /EXTLATCH light pen input
On power-on: WRIO = $FF
Used by the [[multitap]] to select reading of controllers 2/3 vs. 4/5.
{{Anchor|RDIO}}
====RDIO - Read I/O ($4213 read)====
7  bit  0
---- ----
21DD DDDD
|||| ||||
||++-++++- CPU I/O D5-0 (not connected)
|+-------- Joypad port 1 I/O
+--------- Joypad port 2 I/O
The I/O pins allow bidirectional communication between the CPU and joypads on a single wire per bit. Either side is able to set the bits to 0, so to read the value being sent by the other side, the reader must set its own corresponding bits to 1 before reading.
The not-connected D5-0 bits can be used as general-purpose storage on standard consoles, but are used in the [[Super Famicom Box]] hotel system to communicate with its HD64180 CPU.
Joypad port 2's I/O bit is also connected to the PPU's /EXTLATCH input, allowing the PPU's H and V counters to be latched when this bit is set to 0 by the CPU or joypad. This is intended to support a light pen or gun device. This should normally be set to 1 by the CPU to allow the counters to be latched. (See [[PPU_registers#OPHCT|PPU registers]])
===Auto-read results===
----
{{Anchor|JOY1}}
====JOY1L, JOY1H - Joypad port 1 data 1 ($4218, $4219 read)====
  JOY1H      JOY1L
  $4219      $4218
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Joypad port 1 data 1 (first read on left to last read on right)
{{Anchor|JOY2}}
====JOY2L, JOY2H - Joypad port 2 data 1 ($421A, $421B read)====
  JOY2H      JOY2L
  $421B      $421A
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Joypad port 2 data 1 (first read on left to last read on right)
{{Anchor|JOY3}}
====JOY3L, JOY3H - Joypad port 1 data 2 ($421C, $421D read)====
  JOY3H      JOY3L
  $421D      $421C
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Joypad port 1 data 2 (first read on left to last read on right)
{{Anchor|JOY4}}
====JOY4L, JOY4H - Joypad port 2 data 2 ($421E, $421F read)====
  JOY4H      JOY4L
  $421F      $421E
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Joypad port 2 data 2 (first read on left to last read on right)
==Math==
===Multiplication===
----
{{Anchor|WRMPYA}}
====WRMPYA - Multiplication factor A ($4202 write)====
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Multiplication factor (8-bit unsigned)
On power-on: WRMPYA = $FF
{{Anchor|WRMPYB}}
====WRMPYB - Multiplication factor B ($4203 write)====
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Multiplication factor (8-bit unsigned)
On write: Begins multiplication process
The multiplication process takes up to 8 cycles and the result is written to RDMPY as it goes. See 5A22 [[Multiplication]] for more information.
===Division===
----
{{Anchor|WRDIV}}
====WRDIVL, WRDIVH - Dividend ($4204, $4205 write)====
  WRDIVH      WRDIVL
  $4205      $4204
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Dividend (16-bit unsigned)
On power-on: WRDIV = $FFFF
{{Anchor|WRDIVB}}
====WRDIVB - Divisor ($4206 write)====
7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Divisor (8-bit unsigned)
On write: Begins division process
The division process takes up to 16 CPU cycles and the result is written to RDDIV (quotient) and RDMPY (remainder) as it goes. Dividing by 0 results in a quotient of $FFFF and a remainder equal to the dividend (WRDIV). See 5A22 [[Division]] for more information.
===Result===
----
{{Anchor|RDDIV}}
====RDDIVL, RDDIVH - Quotient ($4214, $4215 read)====
  RDDIVH      RDDIVL
  $4215      $4214
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Quotient (16-bit unsigned)
{{Anchor|RDMPY}}
====RDMPYL, RDMPYH - Product or Remainder ($4216, $4217 read)====
  RDMPYH      RDMPYL
  $4217      $4216
7  bit  0  7  bit  0
---- ----  ---- ----
HHHH HHHH  LLLL LLLL
|||| ||||  |||| ||||
++++-++++---++++-++++- Product (16-bit unsigned), or
                        Remainder (16-bit unsigned)
== References ==
<References/>

Latest revision as of 01:54, 2 October 2022

This page covers 5A22, APU, and WRAM memory-mapped registers.

5A22, APU, and WRAM register summary
Name Address Bits Type Notes
APUIO0
APUIO1
APUIO2
APUIO3
$2140
$2141
$2142
$2143
DDDD DDDD RW8 Data to/from APU.
WMDATA $2180 DDDD DDDD RW8 Data to/from S-WRAM, increments WMADD.
WMADDL
WMADDM
WMADDH
$2181
$2182
$2183
LLLL LLLL
MMMM MMMM
.... ...H
W24 S-WRAM address for WMDATA access.
JOYOUT $4016 .... ...D W8 Output to joypads (latches standard controllers).
JOYSER0 $4016 .... ..DD R8 Input from joypad 1.
JOYSER1 $4017 ...1 11DD R8 Always 1 (1), input from joypad 2 (D).
NMITIMEN $4200 N.VH ...J W8 Vblank NMI enable (N), timer IRQ mode (VH), joypad auto-read enable (J).
WRIO $4201 21DD DDDD W8 Joypad port 2 I/O (2), joypad port 1 I/O (1), unused I/O (D).
WRMPYA $4202 DDDD DDDD W8 Unsigned multiplication factor A.
WRMPYB $4203 DDDD DDDD W8 Unsigned multiplication factor B, starts 8-cycle multiplication.
WRDIVL
WRDIVH
$4204
$4205
LLLL LLLL
HHHH HHHH
W16 Unsigned dividend.
WRDIVB $4206 DDDD DDDD W8 Unsigned divisor, starts 16-cycle division.
HTIMEL
HTIMEH
$4207
$4208
.... ...H
LLLL LLLL
W16 H counter target for timer IRQ.
VTIMEL
VTIMEH
$4209
$420A
.... ...H
LLLL LLLL
W16 V counter target for timer IRQ.
MDMAEN $420B 7654 3210 W8 DMA enable.
HDMAEN $420C 7654 3210 W8 HDMA enable.
MEMSEL $420D .... ...F W8 FastROM enable (F).
RDNMI $4210 N... VVVV R8 Vblank NMI flag (N), CPU version (V).
TIMEUP $4211 T... .... R8 Timer IRQ flag (T).
HVBJOY $4212 VH.. ...J R8 Vblank flag (V), hblank flag (H), joypad auto-read in-progress flag (J).
RDIO $4213 21DD DDDD R8 Joypad port 2 I/O (2), joypad port 1 I/O (1), unused I/O (D).
RDDIVL
RDDIVH
$4214
$4215
LLLL LLLL
HHHH HHHH
R16 Unsigned quotient.
RDMPYL
RDMPYH
$4216
$4217
LLLL LLLL
HHHH HHHH
R16 Unsigned product or unsigned remainder.
JOY1L
JOY1H
JOY2L
JOY2H
JOY3L
JOY3H
JOY4L
JOY4H
$4218
$4219
$421A
$421B
$421C
$421D
$421E
$421F
LLLL LLLL
HHHH HHHH
R16 16-bit joypad auto-read result (first read high to last read low).
table source

Register types:

  • R - Readable
  • W - Writeable
  • 8 - 8-bit access only
  • 16 - 8-bit access to either address, or 16-bit access to the lower address.
  • 24 - 8-bit or 16-bit access to 3 registers.

Interrupts

NMITIMEN - Interrupts and Joypad reading ($4200 write)


7  bit  0
---- ----
N.VH ...J
| ||    |
| ||    +- Joypad auto-read enable
| ++------ H/V timer IRQ:
|           00 = Disable timer
|           01 = IRQ when H counter == HTIME
|           10 = IRQ when V counter == VTIME and H counter == 0
|           11 = IRQ when V counter == VTIME and H counter == HTIME
+--------- Vblank NMI enable

On power-on: NMITIMEN = $00
On reset:    NMITIMEN = $00
  • If the vblank NMI is enabled, then an NMI will occur at the start of vblank. More precisely, an NMI occurs whenever the bitwise AND of vblank NMI enable and RDNMI's vblank flag becomes 1. As a result, it is possible to get multiple NMIs for a single vblank if vblank NMI is disabled and enabled again while the vblank flag is still 1. This can be prevented by reading RDNMI, which clears the vblank flag.
  • TODO: Details on the exact conditions for an IRQ.
  • Auto-read runs shortly after the beginning of vblank, reading the current state of the two controller ports into the JOY1-4 registers without halting the CPU. It is equivalent to writing 1 and then 0 to JOYOUT (used for latching standard controllers) and then reading JOYSER0 and JOYSER1 16 times each. The controllers are then left in this state so that additional reads can be done manually from JOYSER0 and JOYSER1 to get any additional data, though this is unnecessary for standard controllers. Auto-read takes approximately 3 scanlines, during which the JOYOUT, JOYSER0, and JOYSER1 registers should not be manually accessed.

Screen timer values


HTIMEL, HTIMEH - H timer target ($4207, $4208 write)

  HTIMEH      HTIMEL
  $4208       $4207
7  bit  0   7  bit  0
---- ----   ---- ----
.... ...H   LLLL LLLL
        |   |||| ||||
        +---++++-++++- H counter target for timer IRQ

On power-on: HTIME = $1FF

Note that setting a value larger than the maximum H counter value of 339 will prevent the timer's H condition from being met.

VTIMEL, VTIMEH - V timer target ($4209, $420A write)

  VTIMEH      VTIMEL
  $420A       $4209
7  bit  0   7  bit  0
---- ----   ---- ----
.... ...H   LLLL LLLL
        |   |||| ||||
        +---++++-++++- V counter target for timer IRQ

On power-on: VTIME = $1FF

Note that setting a value larger than the maximum V counter value will prevent the timer's V condition from being met. The maximum depends on the region (261 for NTSC, 311 for PAL) and interlacing (1 additional scanline every other frame).

Status


RDNMI - Vblank flag and CPU version ($4210 read)

7  bit  0
---- ----
Nxxx VVVV
|||| ||||
|||| ++++- CPU version
|+++------ (Open bus)
+--------- Vblank flag

On power-on: RDNMI = RDNMI & $7F
On reset:    RDNMI = RDNMI & $7F
On read:     RDNMI = RDNMI & $7F

The vblank flag is set at the start of vblank and cleared at the end of vblank or on read.

TIMEUP - Timer flag ($4211 read)

7  bit  0
---- ----
Txxx xxxx
|||| ||||
|+++-++++- (Open bus)
+--------- Timer flag

On power-on: TIMEUP = TIMEUP & $7F
On reset:    TIMEUP = TIMEUP & $7F
On read:     TIMEUP = TIMEUP & $7F

The timer flag is set when the timer condition specified in NMITIMEN becomes true and is cleared on read.

HVBJOY - Screen and Joypad status ($4212 read)

7  bit  0
---- ----
VHxx xxxJ
|||| ||||
|||| |||+- Joypad auto-read in-progress flag
||++-+++-- (Open bus)
|+-------- Hblank flag
+--------- Vblank flag
  • J - Set during joypad auto-read.
  • H - Set during horizontal blank period.
  • V - Set during vertical blank period.

When enabled via NMITIMEN, auto-read begins between H=32.5 and H=95.5 of the first vblank scanline, and ends 4224 master cycles later.[1]

APU

APUIOn - Data-to-APU register n ($214n write) (n = 0..3)

7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Data to APU

APUIOn - Data-from-APU register n ($214n read) (n = 0..3)

7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Data from APU

When the SPC700 reads from $F4+n in its address space, it receives the last value written to APUIOn. When APUIOn is read, the value received is the last one written by the SPC700 to $F4+n. If APUIOn is read while its corresponding $F4+n register is being written, the value read will be the bitwise OR of the old and new values.

These registers are mirrored across $2140-217F.

WRAM

WMDATA - S-WRAM data access ($2180 read/write)


7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- S-WRAM data

On write: [WMADD] = value
          WMADD = WMADD + 1

This register's presence on the peripheral bus allows DMA between S-WRAM and another, different source.

Because DMA simultaneously accesses the source and destination, S-WRAM cannot succesfully be both because it cannot simultaneously read from and write to itself. DMA from S-WRAM to this register has no effect, and DMA from this register to S-WRAM writes open bus. In both cases, the address is not incremented.

WMADDL, WMADDM, WMADDH - S-WRAM address ($2181, $2182, $2183 write)


  WMADDH      WMADDM      WMADDL
  $2183       $2182       $2181
7  bit  0   7  bit  0   7  bit  0
---- ----   ---- ----   ---- ----
.... ...H   MMMM MMMM   LLLL LLLL
        |   |||| ||||   |||| ||||
        +---++++-++++---++++-++++- S-WRAM address for WMDATA

DMA from S-WRAM to these registers has no effect.

ROM

MEMSEL - ROM access speed ($420D write)

 7  bit  0
 ---- ----
 .... ...F
         |
         +- FastROM enable

On power-on: MEMSEL = $00

If enabled, ROM access to banks $80-FF takes only 6 system clock cycles instead of 8.

Joypads

Joypad NES-style interface


JOYOUT - Joypad output ($4016 write)

7  bit  0
---- ----
.... .210
      |||
      ||+- OUT0
      ++-- OUT2-1 (not connected)

OUT0 is used by standard controllers to latch the current button state. OUT2-1 are not connected in standard consoles, but may be used in the Super Famicom Box hotel system.

JOYSER0 - Joypad serial data port 1 ($4016 read)

7  bit  0
---- ----
xxxx xxDD
|||| ||||
|||| ||++- Joypad port 1 data 2-1
++++-++--- (Open bus)

On read: Joypad port 1 is clocked (via joypad 1 /OE)

JOYSER1 - Joypad serial data port 2 ($4017 read)

7  bit  0
---- ----
xxx1 11DD
|||| ||||
|||| ||++- Joypad port 2 data 2-1
|||+-++--- Joypad 2 D4-2 (always 1)
+++------- (Open bus)

On read: Joypad port 2 is clocked (via joypad 2 /OE)

The CPU has 5 joypad 2 inputs. Joypad port 2's data 2 and 1 pins connect to D1-0, while D4-2 are tied to ground (and thus read as 1).

Joypad I/O interface


WRIO - Write I/O ($4201 write)

7  bit  0
---- ----
21DD DDDD
|||| ||||
||++-++++- CPU I/O D5-0 (not connected)
|+-------- Joypad port 1 I/O
+--------- Joypad port 2 I/O, and
           PPU /EXTLATCH light pen input

On power-on: WRIO = $FF

Used by the multitap to select reading of controllers 2/3 vs. 4/5.

RDIO - Read I/O ($4213 read)

7  bit  0
---- ----
21DD DDDD
|||| ||||
||++-++++- CPU I/O D5-0 (not connected)
|+-------- Joypad port 1 I/O
+--------- Joypad port 2 I/O

The I/O pins allow bidirectional communication between the CPU and joypads on a single wire per bit. Either side is able to set the bits to 0, so to read the value being sent by the other side, the reader must set its own corresponding bits to 1 before reading.

The not-connected D5-0 bits can be used as general-purpose storage on standard consoles, but are used in the Super Famicom Box hotel system to communicate with its HD64180 CPU.

Joypad port 2's I/O bit is also connected to the PPU's /EXTLATCH input, allowing the PPU's H and V counters to be latched when this bit is set to 0 by the CPU or joypad. This is intended to support a light pen or gun device. This should normally be set to 1 by the CPU to allow the counters to be latched. (See PPU registers)

Auto-read results


JOY1L, JOY1H - Joypad port 1 data 1 ($4218, $4219 read)

  JOY1H       JOY1L
  $4219       $4218
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Joypad port 1 data 1 (first read on left to last read on right)

JOY2L, JOY2H - Joypad port 2 data 1 ($421A, $421B read)

  JOY2H       JOY2L
  $421B       $421A
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Joypad port 2 data 1 (first read on left to last read on right)

JOY3L, JOY3H - Joypad port 1 data 2 ($421C, $421D read)

  JOY3H       JOY3L
  $421D       $421C
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Joypad port 1 data 2 (first read on left to last read on right)

JOY4L, JOY4H - Joypad port 2 data 2 ($421E, $421F read)

  JOY4H       JOY4L
  $421F       $421E
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Joypad port 2 data 2 (first read on left to last read on right)

Math

Multiplication


WRMPYA - Multiplication factor A ($4202 write)

7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Multiplication factor (8-bit unsigned)

On power-on: WRMPYA = $FF

WRMPYB - Multiplication factor B ($4203 write)

7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Multiplication factor (8-bit unsigned)

On write: Begins multiplication process

The multiplication process takes up to 8 cycles and the result is written to RDMPY as it goes. See 5A22 Multiplication for more information.

Division


WRDIVL, WRDIVH - Dividend ($4204, $4205 write)

  WRDIVH      WRDIVL
  $4205       $4204
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Dividend (16-bit unsigned)

On power-on: WRDIV = $FFFF

WRDIVB - Divisor ($4206 write)

7  bit  0
---- ----
DDDD DDDD
|||| ||||
++++-++++- Divisor (8-bit unsigned)

On write: Begins division process

The division process takes up to 16 CPU cycles and the result is written to RDDIV (quotient) and RDMPY (remainder) as it goes. Dividing by 0 results in a quotient of $FFFF and a remainder equal to the dividend (WRDIV). See 5A22 Division for more information.

Result


RDDIVL, RDDIVH - Quotient ($4214, $4215 read)

  RDDIVH      RDDIVL
  $4215       $4214
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Quotient (16-bit unsigned)

RDMPYL, RDMPYH - Product or Remainder ($4216, $4217 read)

  RDMPYH      RDMPYL
  $4217       $4216
7  bit  0   7  bit  0
---- ----   ---- ----
HHHH HHHH   LLLL LLLL
|||| ||||   |||| ||||
++++-++++---++++-++++- Product (16-bit unsigned), or
                       Remainder (16-bit unsigned)

References

  1. Auto Joypad Read timings from Anomie's timing.txt document.